Why a Spiral Around a Tree Is Different
A spiral staircase winding up around a trunk is one of the most striking ways to reach a treehouse. It also differs from an indoor spiral stair in two important ways:
- The centre is a living, growing, moving tree, not a steel pole. The trunk gets wider every year and sways in the wind.
- The inner radius is large. An indoor spiral wraps around a narrow pole, so the inner end of each tread is very narrow. Around a tree, the inner edge sits well out from the centre, so treads can be much more comfortable to walk on.
Get the first point right and the second works in your favour.
Don’t Use the Trunk as the Centre Column
It’s tempting to fix every tread directly to the trunk. For most builds it’s a poor idea:
- A full spiral can need a dozen or more treads, and fixing each one to the trunk means many wounds in a band around the tree
- The trunk keeps growing, so anything fixed tight to it gets squeezed or pushed out over time
- The tree moves in wind while the ground doesn’t, which strains any fixing that ties the two together
A better approach is a stair that stands on its own supports, with the inner edge of the treads kept clear of the bark. If part of the stair must bear on the tree, limit it to a small number of proper treehouse bolts, as explained in how to attach a treehouse to a tree without harming it, and have the design checked by someone experienced.
Three Ways to Support the Stair
1. Outer posts with a curved (helical) stringer. A ring of posts on footings carries a curved outer stringer. The treads fix to the stringer and cantilever inwards, stopping short of the trunk. This looks elegant but takes skill: the stringer is usually laminated from thin strips bent over a form.
2. Inner and outer posts. Two rings of posts, one close to the trunk (but with footings set back from the main roots) and one outside, carry the treads at both ends. It’s sturdier and easier to build, and the inner posts can double as a guard.
3. Short straight flights with landings (a “polygonal spiral”). Instead of a true curve, build three or four short straight flights with small landings or winder steps, each turning part of the way around the trunk on its own posts. This is by far the easiest for most DIY builders, and it still gives the wraparound effect.
Whichever you choose, keep footings away from the trunk where you can to limit root damage, and avoid heavy digging close to the tree.
How to Lay Out a Spiral Staircase Around a Tree
Step 1: Measure the Total Rise
Measure from the finished ground level at the bottom to the top of the finished platform. Ground is rarely level around a tree, so measure at the exact spot where the stair will start.
Step 2: Choose the Number of Risers
Divide the total rise by a comfortable riser height. Somewhere around 170–220 mm (about 7–8½ in) is a common range for outdoor stairs. Round to a whole number of risers, then divide the total rise by that number to get your exact riser height. Every step must be the same height, because uneven steps are a classic trip hazard.
The number of treads is one less than the number of risers, because the platform itself acts as the top step.
Step 3: Set the Inner and Outer Radius
Measure the trunk diameter at the height of the stair (it can vary), then:
- Inner radius = half the trunk diameter + a clearance gap for growth and sway (often 10–15 cm or more)
- Outer radius = inner radius + tread length (the width you walk across)
A tread length of about 70–90 cm (28–36 in) feels comfortable for one person at a time.
Step 4: Choose the Rotation per Tread
Decide how many degrees each tread turns. A smaller angle gives deeper treads but needs more of a turn to reach the top. Then check the going (the depth of tread you actually step on) along the walking line, roughly halfway along the tread:
Going at walking line = 2 × π × walking-line radius × (degrees per tread ÷ 360)
Step 5: Check Headroom
After one full turn, you’ll pass under the treads you’ve already climbed. Headroom at that point is roughly the height gained in one turn minus the tread thickness. If it’s too low, increase the rotation per tread (fewer treads per turn) or rethink where the stair starts.
Step 6: Mark It Out on the Ground
Drive a stake close to the trunk’s centre line, or use the trunk itself with a loop of string around it, and use a string line to mark the inner and outer radii. Mark radial lines for each tread with a large protractor or by measuring chord lengths. Mark where the top tread must arrive at the platform opening, and work backwards from there.
Worked Example
Suppose:
- Total rise to the platform: 3,000 mm
- Trunk diameter: 500 mm
Risers: 3,000 ÷ 200 = 15 risers of 200 mm, so 14 treads.
Radii: inner radius = 250 + 150 clearance = 400 mm. With 700 mm treads, outer radius = 1,100 mm, so the stair is about 2.2 m across.
Rotation: at 30° per tread, 12 treads make a full turn. 14 treads × 30° = 420°, a little over one full turn.
Going at walking line: taking the walking line at the middle of the tread (750 mm radius): 2 × π × 750 × (30 ÷ 360) ≈ 390 mm. That’s a generous, comfortable going, much better than a tight indoor spiral, thanks to the large inner radius.
Headroom: one full turn is 12 risers × 200 mm = 2,400 mm. Subtract a 50 mm tread and you have about 2.35 m of clearance where the stair passes over itself. That works.
Treat this as an illustration of the method, not a design for your tree.
Treads, Handrails and Guarding
- Treads: use durable, slip-resistant timber, thick enough not to bounce, and fix them securely. Hardwood or thick treated softwood both work. Our guide to the best timber for a treehouse has options.
- Outer handrail: a continuous handrail on the outside is essential. Vertical balusters with small gaps stop children slipping through. Spacing guidance commonly works on the principle that a 100 mm (4 in) sphere shouldn’t pass through.
- The inner gap: the space between the treads and the trunk can be a fall or trapping hazard, especially for small children. Either keep it narrow while still leaving room for growth, or add an inner guard on posts.
- Open risers: gaps between treads can let small children slip through. Consider riser boards or extra rails if young children will use the stair.
- Top and bottom: fit a gate at the top if young children use the platform, and make sure the stair meets the railings with no gaps.
Can You Use a DIY Spiral Staircase Kit?
Most spiral staircase kits are built around a central steel column, with treads radiating from it, so they won’t wrap around a tree. Some large-diameter outdoor kits exist, but the trunk usually leaves no room for the column. A kit can work beside a tree rather than around it, as a compact way to reach a platform. Otherwise, a tree-wrapping stair is almost always a custom carpentry job.
Rules and Cost
Spiral stairs are subject to building rules when they’re part of a home. A treehouse stair may or may not be covered, depending on where you live and what the treehouse is used for. See is it legal to have a spiral staircase? for an overview.
Costs vary hugely with materials and whether you build it yourself. See the average cost to install a spiral staircase for ballpark figures and what drives them. For the platform it leads to, see how to build a treehouse platform step by step.