Design and Building

Building a Treehouse Between Two Trees: Allowing for Movement

How to build a treehouse between two trees that sway independently: fixed and floating supports, sliding brackets, layouts, how much movement to allow and checks.

On this page
  1. Why Two Trees Need Special Treatment
  2. The Basic Principle: One Fixed, One Free
  3. Common Two-Tree Layouts
  4. Hardware That Allows Movement
  5. How Much Movement Should You Allow?
  6. Choosing and Measuring the Trees
  7. Step by Step
  8. Walls, Roofs and Movement
  9. Inspection and Maintenance

Why Two Trees Need Special Treatment

A platform spanning two trees can be bigger and more stable than one in a single tree, but there’s a catch: the two trees move independently. In wind, each trunk sways in its own direction, at its own speed and by its own amount. Over the years, both also grow wider.

If you bolt a beam rigidly to both trunks, something has to give. The forces of two swaying trees can bend or loosen bolts, split beams, tear fixings out of the wood, and damage the trees. The key to a two-tree treehouse is letting the trees move without dragging the structure with them.

The Basic Principle: One Fixed, One Free

The most common approach:

  • Fix the beams firmly to one tree, so the platform is anchored and can’t wander
  • Let the beams slide on the other tree, usually on a floating (sliding) bracket, so that trunk can move back and forth without pushing or pulling on the structure

Think of the platform as resting on the second tree rather than being tied to it, while being held so it can’t slide off.

Common Two-Tree Layouts

Fixed on One Tree, Floating on the Other

Two parallel beams run between the trees, one on each side of the trunks. At tree A, each beam sits on a treehouse bolt with a fixed bracket. At tree B, each beam sits on a bolt with a floating bracket that allows it to slide. It’s simple and widely used.

Floating Brackets on Both Trees

On some designs, especially where the trees are far apart or very flexible, both ends are allowed to move, with the platform held in place by its own weight, stops on the brackets, and careful geometry. This is more complicated to design, and it’s worth getting experienced advice.

Two Platforms and a Bridge

If the trees are far apart or very different in size, build a separate platform in each tree and connect them with a rope or plank bridge designed to flex. Each platform then only has to cope with its own tree.

Two Trees Plus Posts

Adding ground posts under part of the platform reduces the load on the trees and allows a bigger structure. The same rule applies: connections to the trees must still allow movement, because posts stay still while trees sway.

Hardware That Allows Movement

  • Floating (sliding) brackets: fit over a treehouse bolt and hold the beam while allowing it to slide along a slot
  • Treehouse attachment bolts: the base for most brackets. They hold the beam clear of the trunk so the tree can grow
  • Cable suspension: a cable from higher in the tree to the platform can carry load while allowing some movement, but it can let the platform swing
  • Slider plates: some builders use low-friction plates under the beam on the free end, but purpose-made brackets are generally more predictable

Use brackets designed for your bolt system. See treehouse fixings and accessories and how to attach a treehouse to a tree without harming it.

How Much Movement Should You Allow?

There’s no single figure. Movement depends on the species, height, trunk size, exposure and the distance between the trees. A few principles:

  • Higher in the tree means more movement. Trunks sway more the further up you go, which is another reason to build lower
  • Thinner, taller trees move more than thick, short ones
  • Exposed sites move more than sheltered ones
  • Allow generously. Use the full range of travel your floating brackets offer, and make sure the beam can’t slide off the end of the bracket

Watch the trees on a windy day before you build. Tie a string or ribbon between them at your planned height and see how much it tightens and slackens.

Choosing and Measuring the Trees

  • Both trees need to be healthy and strong. Check each one separately. See best trees for a treehouse (and which to avoid)
  • Similar size and species help. Two similar trees tend to move more similarly than a large oak and a slender birch
  • Spacing: the distance between trunks sets the beam span. Longer spans need bigger beams, and very wide gaps may suit the two-platforms-and-a-bridge approach
  • Measure at the planned height, not at the ground, because trunks may lean towards or away from each other

Step by Step

  1. Decide which tree is fixed. Usually it’s the sturdier tree, or the one nearer the access.
  2. Mark a level line across both trunks with a laser level.
  3. Install treehouse bolts on each side of each trunk, following the manufacturer’s instructions.
  4. Fit fixed brackets on the fixed tree and floating brackets on the free tree.
  5. Lift and seat the beams. Check they’re level and parallel, and that the floating ends sit in the middle of the slot’s travel.
  6. Add knee braces if the beams cantilever beyond the trees. On the floating end, any brace must not lock the beam to the tree.
  7. Frame the joists across the beams, with generous openings around both trunks.
  8. Lay the decking and fit railings.
  9. Check for anything that ties the platform rigidly to the free tree, such as railings, ladders or roof members fixed to both.

For the detailed framing steps, see how to build a treehouse platform step by step.

Walls, Roofs and Movement

Movement doesn’t stop at the platform. Anything fixed to both the structure and the free tree can transmit movement:

  • Don’t fix walls or roof framing to the free tree
  • Leave gaps where trunks pass through walls or roofs, and seal them with flexible collars or boots rather than rigid flashing. See treehouse roof options
  • Keep it light: heavy enclosed cabins increase loads on both the trees and the floating brackets

Inspection and Maintenance

  • After storms, check that the floating ends are still within their slots and moving freely
  • Once a year, check all bolts and brackets, look for wear on sliding surfaces, and check the growth gaps around both trunks
  • Watch the trees for signs of stress, such as dieback, fungi or cracks. See how to attach a treehouse to a tree without harming it

For the bigger design picture, see how to design and build a beautiful treehouse.

The complete guide to design and building

How to Design and Build a Beautiful Treehouse
Read the guide

Keep exploring

Guides from other topics

All topics →